- 欢迎光临Satisfactory国区BWIKI。请登录您的B站账号,方可使用页面编辑与评论功能。

全站通知:

管道泵

阅读

    

2020-07-17更新

    

最新编辑:Liwers_Loor

阅读:

  

更新日期:2020-07-17

  

最新编辑:Liwers_Loor

来自幸福工厂WIKI_BWIKI_哔哩哔哩
跳到导航 跳到搜索
页面贡献者 :
可爱的乖猫猫Liwers

This article is a stub. You can help 幸福工厂WIKI_BWIKI_哔哩哔哩 by expanding it.

{{#cargo_store: _table = buildings
Pipeline Pump
Pipeline Pump.png
Can be attached to a Pipeline to apply Head Lift. Maximum Head Lift: 20 meters. (Allows fluids to be transported 20 meters upwards.) Outputs fluid at 300m模板:Cubic per minute.
Note: Has an in- and output direction.
Note: Head Lift does not stack, so space between Pumps is recommended.
解锁 Tier 3 - Coal Power
分类 Logistics
二级分类 Pipelines
用电量 4 MW
能否超频 No
规模
宽度 2 m
长度 5 m
高度 2 m
name = Pipeline Pump researchTier = Tier 3 - Coal Power powerUsage = 4 powerGenerated = fuel = overclockable = No inputs = outputs = width = 2 length = 5 height = 2 sizeNote =

}}

制作
制作途径 Build Gun
所需零件
材料
Copper Sheet.png
2
Rotor.png
2
模板:ResourceBreakdown

{{#cargo_store:_table = crafting_recipes

product = Pipeline Pump recipeName = Pipeline Pump experimental = unreleased = alternateRecipe = 0 mainRecipe = 1 researchTier = Tier 3 - Coal Power craftedIn = Build Gun inCraftBench = inWorkShop = craftingTime = craftingClicks = productCount = productsPerMinute = 0 product2 = productCount2 = productsPerMinute2 = 60 product3 = productCount3 = productsPerMinute3 = 60 product4 = productCount4 = productsPerMinute4 = 60 quantity1 = 2 ingredient1 = Copper Sheet quantity2 = 2 ingredient2 = Rotor quantity3 = ingredient3 = quantity4 = ingredient4 = quantity5 = ingredient5 = quantity6 = ingredient6 = quantity7 = ingredient7 = quantity8 = ingredient8 = quantity9 = ingredient9 = quantity10 = ingredient10 =

}}

The Pipeline Pump is a building used to increase Pipeline pressure. It is directional, which is denoted with two arrows in its blueprint and also on the structure itself. It can be either built separately or attach to an already built Pipeline. A Pipeline Pump also snaps to Walls, making it easier to build pumps exactly 20 meters apart vertically.

Head Lift

文件:Pipeline Pump max Head Lift.png
The recommended head lift of 20m has been exceeded, but the output is still at full 300m³/min. The 2m wide error margin is indicated by the orange segment of the Head Lift-gauge on the right side.
  • Fluids have a Head Lift that dictates how far upwards they can travel in Pipelines. In short terms, a 1m rise requires a Head Lift of 1m, a rise of 10m requires a Head Lift of 10m and so on.
  • The Head Lift's lowest point is measured at the geometrical center of a pipeline pump or the pipe connector of a fluid outputting building. Fluid Buffers are the only excption, with their Head Lift being measured upwards from the bottom of the building.
  • Water Extractor.png Water, Oil Extractor.png Oil Extractors and Refinery.png Refineries provide recommended head lift of 10 meters + 2 meters beyond limit. Pipeline Pumps output at a "Recommmended Max Head Lift" of 20m + 2m beyond limit, thereby having a theoretical maximum Head Lift of 22m, yet practically the limit is at around 23m, after which flow rate will drop sharply and reach 0 m³/min at around 23.3m.
  • Note that the applied Head Lift is not accumulative, it is therefore necessary to space out the pumps evenly if the rise exceeds 20m and that the maximum Head Lift shown in the Pumps UI is 22m.
  • If multiple sources connected to a pipeline have different Head Lifts, then the highest Head Lift will be applied to the entire connected network. This makes Head Lift exploits possible provided water bodies at different heights are in close proximity such as near the waterfalls.
    • To do so, first construct as many water extractors at the lower water body as you need.
    • Build a floating factory above the lower extractors, but lower than the water level of upper water body. Connect the water pipes between the factory needing the water and those extractors.
    • Construct 1 water extractor at the upper water body. Extend a water pipe down the waterfall and to connect this extractor to all the other pipes at the lower part.
    • All the pipes will then share the head lift of the highest water extractor.
    • For this setup, Pipeline Pumps are not required at all.

Flow direction

A Pipeline pump has a direction, as indicated by the arrows on its building hologram. Even when unpowered, a Pipeline Pump also act as a one-way valve: It prevents fluids from flowing backwards. The pistons of the pump are always pointed backwards against the fluid flow direction.

Flow rate

  • A Pipeline Pump outputs the fluid at the speed which it receives them, it will not increase the flow rate.
  • Refering to the description "Outputs fluids at 300 m模板:Cubic per minute" it might have a maximum work capacity of 300m³/min. Unfortunately, this is currently not verifiable because the Pipelines also max out at 300m³/min, but the description "Useful for [...] balancing out throughput" further deepens this claim while also hinting at faster pipelines. (Also by the UI of the Water Extractor, stating a Max Flow Rate of 600m³/min for the internally stored water and the Oil Extractor on pure nodes overclocked at 250% with also an output of 600m³/min.)

Unpowered pump

  • An unpowered pump still allows fluid to flow through in 1-direction, allowing it to act as a one-way valve.

Snapping

  • A Pipeline Pump can be snapped to an existing pipeline, similar to a splitter.
  • A Pipeline Pump can be placed on Foundations for precise placement. You can rotate it in 90 degrees interval horizontally.
  • A Pipeline Pump can be placed on Walls for precise placement. You can rotate it in 45 degrees interval vertically.

Gallery

History

External link